Touchmix App For Laptop Mac

  1. Touchmix App For Laptop Macbook Pro
  2. Touchmix App For Laptop Mac Free
  3. Touchmix App For Laptop Mac Computers
  4. Touchmix App For Laptop Machine

Since TouchMix is an Android app and cannot be installed on Windows PC or MAC directly, we will show how to install and play TouchMix on PC below: Firstly, download and install an Android emulator to your PC Download TouchMix APK to your PC Open TouchMix APK using the emulator or drag and drop the.APK file into the emulator to install the app. Once connected to the router on your device, launch the QSC TouchMix app. If the app shows “Disconnected” in red in the upper right hand corner, press the “Menu” button, go. To “Network” and select your mixer from the “Found Mixers” list and press “Select.”.

TouchMix-30 Pro – New Firmware v2.0 & Windows DAW driver

With firmware version 2.0, TouchMix-30 Pro now supports 3 custom fader banks of 8 channels each, allowing versatile, personalized channel display for the most demanding users and applications. Firmware v2.0 also gives the TouchMix-30 Pro the capability to interface with select third party control surfaces with motorized faders using Mackie Control Protocol. Two modes of operation exist: TouchMix-30 Pro mixer wired to the control surface, or iOS tablet paired with the control surface and connected to the TouchMix-30 Pro mixer via Wi-Fi. The complementary new channel strips display presents controls and indicators for the selected fader group.

The new, updated Windows DAW driver allows for a more robust connection to Windows computers and enable plug-in’s to run on Windows DAW’s and on Waves MultiRack.

Control App

Firmware

Please read the PC or macOS® installation instructions below prior to downloading firmware

  • Download Version 2.0.11665 01/28/2020

Windows USB Driver

  • Download Windows USB Driver 6/10/2019

MacOS

Touchmix App For Laptop Macbook Pro

TouchMix-30 Pro supports macOS® DAW natively via Core Audio. No additional driver required.

Release Notes for TouchMix-30 Firmware Version 2.0.11665

New Features / Improvements

This is a maintenance release and does not add any new features or functionality. See below for a list of the bugs we’ve squashed. Before you install the firmware remember the 1st rule of shows…

If you are about to do a show with your gear set up and working don’t be changing things. Give yourself time to do the upgrade and get all the mixer’s settings squared away.

Bug Fixes (Mixer)

  • Fixed a bug that could cause the mixer to crash when a very large number of screens have been loaded.
  • Repaired an issue that could cause the compressor to operate improperly when certain channels are selected as a Side Chain source.
  • Addressed a bug that could cause Stereo In 27/28 to display the audio level of Stereo In 29/30 when Stereo In 29/30 is selected as a Side Chain source.
  • Rectified a bug that caused all input channels to be assigned to the Main L/R mix when a Channel Reset was performed on the Main L/R even if the input channels had been unassigned.
  • Corrected a problem that caused the Compressor on Ch. 20 to become inoperative.
  • Remedied an issue that could cause Inputs 19 and 20 to send distortion/noise at a high level with a certain combination of settings.

Bug Fixes (iPadOS)

  • Fixed a problem that could prevent display of the channel name label and gain indication.

Release Notes for TouchMix-30 Firmware Version 2.0.11265

New Features / Improvements

Bug Fixes

  • Fixed a bug that could cause the master rotary encoder and other controls to become sluggish or unresponsive.
  • Fixed a bug that can cause Aux mix names and linking to be reset to factory default settings.
  • Minor corrections to text and labelling.

Release Notes for TouchMix-30 Firmware Version 2.0.11095

New Features / Improvements

In response to user requests, the 2.0 release adds significant new capabilities to the TouchMix-30 Pro.

  • Support for external control by third-party, motorized-fader control surfaces directly connected to the mixer via MIDI-over-USB.
  • Support for external control by third-party, motorized-fader control surfaces directly connected to an iOS tablet via MIDI-over-USB.
  • Adds a new External Faders mode (Menu > External Faders) that displays a channel strip view on screen when used with an external control surface.
  • Adds three Custom Fader Banks (Menu > Custom Banks) that may be easily configured to include any combination of input, output, FX return, sub-group and DCA group faders.
  • Improved Solo In Place (SIP) operation. FX returns are no longer affected by SIP.
  • Additional input channel presets for percussion (cajon, djembe, timbale, percussion toys), electronic drum kit, harmonica, flute, cello, accordion and various Banda instruments. Adjustments were also made to vocal and bass presets.
  • Added support for CP Series Compact Powered Loudspeakers.

Bug Fixes

  • Fixed a bug that caused only the left channel of a linked pair to be shown in the Auto-Mixer view.
  • Fixed a bug that caused channels 19 and 20 to output noise under a specific combination of conditions.

Known Issues

  • Internal info system has not been updated to reflect the features and improvements described above.
  • Connection of external control surfaces to Android devices is not supported and there is currently no plan to do so.
  • Android Only - The Phones button may show as being engaged when it is not.
  • When multiple tablets are used to control a mixer and Simple Mode is enabled on one of the tablets, it may cause an erratic display of the same function on the other tablets.
  • After a 3rd party control surface is connected, the mixer may need to be power-cycled before the control surface is recognized.
  • The mixer does not reconnect to a network after a firmware update. This is normal operation. A notification that a power cycle is required is displayed on the mixer following the update.
  • Before updating your mixer be sure to allow yourself ample time before your next use of the mixer.
  • Problems with updating? Go to the TouchMix-30 Pro Updater Recovery Instructions page for help.
  • Start firmware Download.

Windows Download and Installation
Revised 06/07/2017

The following instructions apply to a download that is performed using a Windows computer.

  1. Download the latest firmware from the QSC website. By default, the file will be saved to Downloads on your computer.
  2. Drag the downloaded file onto your desktop.
  3. Unzip the downloaded file by double clicking it. The extracted contents will be a new .install file which will appear on the desktop.
  4. Prepare a USB thumb-drive, SSD or HD with 1GB of available storage space formatted FAT32. For best results, use a freshly formatted drive. The easiest way to perform the format is by using the TouchMix-30 format utility which may be found in the Recording Setup (Record/Play > Recording Setup).
  5. Copy the .install file onto the USB storage device. The file on the storage device will be in the format 'V1.2.0000.install'. The version number will vary depending on the release but the file will always end with extension '.install'.
  6. Safely eject the USB storage device from your computer.
  7. Insert the USB storage device into one of the two USB ports on the mixer's rear panel. Note that the mixer will only recognize one USB storage device at a time.
  8. Press the Menu button, then touch the Mixer Setup button.
  9. On the Mixer Setup screen, touch the Upgrade button. A dialog box displays with some IMPORTANT information about saving the mixer's current settings.
  10. Touch the Proceed button to continue the upgrade. The mixer will boot into the Software Upgrader program. This takes a few minutes.
  11. Select the upgrade file you want to use. If you downloaded to a freshly formatted drive, there will be only one upgrade file displayed.
  12. Touch the Upgrade button to begin the upgrade process. This can take up to 10 minutes and must not be interrupted.
  13. When the upgrade is complete, a dialog displays indicating the upgrade was successful. Press the OK button to exit the Software Upgrader and reboot the mixer.
  14. If you experience problems connecting to tablets and smartphones, put the mixer into Standby disconnect AC power for a few seconds and then reconnect.

* In the event that the update fails, a Recovery Utility is available for download.

macOS Download and Installation
Revised 06/07/2017

The following instructions apply to a download that is performed using a macOS computer.

  1. Download the latest firmware from the QSC website. By default, the file will be saved to Downloads on your computer.
  2. Drag the downloaded file onto your desktop.
  3. Unzip the downloaded file by double clicking it. The extracted contents will be a new .install file which will appear on the desktop.
  4. Prepare a USB thumb-drive, SSD or HD with 1GB of available storage space formatted FAT32. For best results, use a freshly formatted drive. The easiest way to perform the format is by using the TouchMix-30 format utility which may be found in the Recording Setup (Record/Play > Recording Setup).
  5. Copy the .install file onto the USB storage device. The file on the storage device will be in the format 'V1.2.0000.install'. The version number will vary depending on the release but the file will always end with extension '.install'.
  6. Safely eject the USB storage device from your computer.
  7. Insert the USB storage device into one of the two USB ports on the mixer's rear panel. Note that the mixer will only recognize one USB storage device at a time.
  8. Press the Menu button, then touch the Mixer Setup button.
  9. On the Mixer Setup screen, touch the Upgrade button. A dialog box displays with some IMPORTANT information about saving the mixer's current settings.
  10. Touch the Proceed button to continue the upgrade. The mixer will boot into the Software Upgrader program. This takes a few minutes.
  11. Select the upgrade file you want to use. If you downloaded to a freshly formatted drive, there will be only one upgrade file displayed.
  12. Touch the Upgrade button to begin the upgrade process. This can take up to 10 minutes and must not be interrupted.
  13. When the upgrade is complete, a dialog displays indicating the upgrade was successful. Press the OK button to exit the Software Upgrader and reboot the mixer.
  14. If you experience problems connecting to tablets and smartphones, put the mixer into Standby disconnect AC power for a few seconds and then reconnect.

* In the event that the update fails, a Recovery Utility is available for download.

Direct Download and Installation
Revised 06/07/2017

When connected to the internet, TouchMix-30 Pro mixers with software version 1.1 or higher can check for and download subsequent software updates. If an update is available, a message will appear with some information about it. You may dismiss the message or proceed with the update.

  1. You will need:
    • A reliable internet connection.
    • A connection between the mixer and the internet router.
    • A USB thumb-drive, SSD or HD with 1GB of available storage space formatted FAT32. For best results, use a freshly formatted drive.
  2. Insert the formatted USB drive into one of the mixer's USB ports.
  3. Initiate the download (Menu > Mixer Setup > Download Upgrade).
  4. A message will appear 'Contacting the Server'.
    • If the mixer already has the latest version installed or if the server is not available a message will appear 'The latest version is installed'.
  5. Touch the confirmation prompts and the mixer will download the update to the USB drive.
  6. Upon completion, a 'Download Successful' message will be displayed.
    • If this message is not displayed, the complete update has not been downloaded. Check your internet connections and try again or use your computer to download the update from www.qsc.com.
  7. Press the Menu button, then touch the Mixer Setup button.
  8. On the Mixer Setup screen, touch the Upgrade button. A dialog box displays IMPORTANT information about saving the mixer's current settings.
  9. Touch the Proceed button to continue the upgrade. The mixer will boot into the Software Upgrader program. This takes a few minutes.
  10. Select the upgrade file you want to use. If you downloaded to a freshly formatted drive, there will be only one upgrade file displayed.
  11. Touch the Upgrade button to begin the upgrade process. This can take up to 10 minutes and must not be interrupted.
  12. When the upgrade is complete, a dialog displays indicating the upgrade was successful. Press the OK button to exit the Software Upgrader and reboot the mixer.
  13. If you experience problems connecting to tablets and smartphones, put the mixer into Standby disconnect AC power for a few seconds and then reconnect.

Control App

Firmware

Please read the PC or macOS® installation instructions below prior to downloading firmware

  • Download Version 3.0.09551 8/6/2018

Release Notes for Firmware Version 3.0.09551

New Features / Improvements (Mixer):

  • This is a maintenance release only and does not include any significant changes to features or functionality.

Bug Fixes (Mixer)

  • Fixed a bug that caused FX to stop working after extended operation.
  • Fixed a bug that caused unexpected operation of the stereo delay effect when the Tempo window is selected and the encoder wheel is turned.
  • Fixed a bug that caused a stereo meter to appear on a mono aux output when the Anti-Feedback tab is selected.
  • Fixed a bug that caused the Ethernet driver to crash (requiring a power cycle to recover) when an invalid value for the Network Setup Gateway is entered.

Bug Fixes (Android)

  • Changes in the Android OS and Chrome browser could cause a condition in which meter activity on the Android device would cause the Android app to crash. This has been remedied with this release.

Touchmix App For Laptop Mac Free

App

Windows Download and Installation
Revised 06/07/2017

The following instructions apply to a download that is performed using a Windows computer.

Touchmix App For Laptop Mac Computers

  1. Download the latest firmware from the QSC website.
  2. Unzip the downloaded file. The extracted contents will be a tar.gz file.
  3. Prepare a USB thumb-drive, SSD or HD with 1GB of available storage space formatted FAT32. For best results, use a freshly formatted drive.
  4. Copy the .tar.gz file onto the USB storage device. The file on the storage device will be in the format 'V3.0.0000.tar.gz'. The version number will vary depending on the release but the file will always end with extension 'tar.gz'.
  5. Insert the USB storage device into one of the two USB ports on the mixer's rear panel.
  6. Press the Menu button, then touch the Mixer Setup button.
  7. On the Mixer Setup screen, touch the Upgrade button. A dialog box displays with some IMPORTANT information about saving the mixer's current settings.
  8. Touch the Proceed button to continue the upgrade. The mixer will boot into the Software Upgrader program. This takes a few minutes.
  9. Select the upgrade file you want to use. If you downloaded to a freshly formatted drive, there will be only one upgrade file displayed.
  10. Touch the Upgrade button to begin the upgrade process. This can take up to 10 minutes.
  11. When the upgrade is complete, a dialog displays indicating the upgrade was successful. Press the OK button to exit the Software Upgrader and reboot the mixer.
  12. If you experience problems connecting to tablets and smartphones, put the mixer into Standby disconnect AC power for a few seconds and then reconnect.

macOS Download and Installation
Revised 06/07/2017

The following instructions apply to a download that is performed using a macOS computer.

Before you download!
The TouchMix updater expects to see a zipped tar.gz folder. Macintosh computers include features that automatically unzip downloaded folders and they seem quite insistent about doing so.

Before downloading the file follow these steps:

Touchmix App For Laptop Machine

  1. Launch the finder on your Mac and Type 'Archive Utility' in the search field.
    • To locate the Archive Utility manually – double-click the icon for the drive containing your computer's system, follow the path: System/Library/CoreServices/Applications.
  2. If you do not have access to your Macintosh HD, click anywhere on your desktop, click the word 'Finder' in the upper left hand corner of your desktop and select preferences. In the general tab, under 'Show these items on the desktop:' check the box next to 'Hard Disks' and your Macintosh HD will appear on the desktop. You can then follow the path above to access the Archive Utility.
  3. Double click the Archive Utility icon to Launch the application.
  4. On the Menu Bar at the top of the screen, click on 'Archive Utility' and select 'preferences' from the drop down menu.
  5. On the Archive Utility Preferences window, uncheck 'Keep expanding if possible'.
  6. If using Safari- Double click the 'Safari' icon to launch the browser.
  7. On the menu bar at the top of the screen, click on 'Safari' and select 'Preferences' from the dropdown menu.
  8. On the Safari Preferences window, uncheck 'Open safe files after downloading'.

Your macOS computer will now download the upgrade without unzipping it.

  1. Download the latest firmware from the QSC website.
  2. Drag the downloaded file onto your desktop
  3. Unzip the downloaded file by double clicking it. This extracts the tar.gz file from the zipped folder but leaves the tar.gz file itself unzipped. This is what the mixer expects to see.
  4. Prepare a USB thumb-drive, SSD or HD with 1GB of available storage space formatted FAT32. For best results, use a freshly formatted drive. Performing a FAT32 format using a macOS computer can be a bit tricky. Here's how to do it.
    • Connect the drive to your computer and launch the Disc Utility.
    • In the Disk Utility left column, select the drive.
    • Select Erase.
    • Select Format. Then select MS-DOS (FAT).
    • Select Scheme. Then select Master Boot Record.
    • Click Erase. The utility will now format the drive properly for use with TouchMix. Exit the Disk Utility when you are done.
  5. Copy the .tar.gz file onto the USB storage device. The file on the storage device will be in the format 'V3.0.0000.tar.gz'. The version number will vary depending on the release but the file will always end with extension 'tar.gz'.
  6. Safely eject the USB storage device from your Mac.
  7. Insert the USB storage device into one of the two USB ports on the mixer's rear panel.
  8. Press the Menu button, then touch the Mixer Setup button.
  9. On the Mixer Setup screen, touch the Upgrade button. A dialog box displays with some IMPORTANT information about saving the mixer's current settings.
  10. Touch the Proceed button to continue the upgrade. The mixer will boot into the Software Upgrader program. This takes a few minutes.
  11. Select the upgrade file you want to use. If you downloaded to a freshly formatted drive, there will be only one upgrade file displayed.
  12. Touch the Upgrade button to begin the upgrade process. This can take up to 10 minutes.
  13. When the upgrade is complete, a dialog displays indicating the upgrade was successful. Press the OK button to exit the Software Upgrader and reboot the mixer.
  14. If you experience problems connecting to tablets and smartphones, put the mixer into Standby disconnect AC power for a few seconds and then reconnect.

Sign-up for TouchMix Notifications

You have already submitted this form. Please visit our Subscription Management Page to update your preferences.